CPH6329 no.8001-1/4 sanyo electric co.,ltd. semiconductor company tokyo office tokyo bldg., 1-10, 1 chome, ueno, taito-ku, tokyo, 110-8534 japan ordering number : enn8001 CPH6329 p-channel silicon mosfet general-purpose switching device applications features ? low on-resistance. ? ultrahigh-speed switching. ? 2.5v drive. specifications absolute maximum ratings at ta=25 c parameter symbol conditions ratings unit drain-to-source voltage v dss -- 30 v gate-to-source voltage v gss 10 v drain current (dc) i d --2.0 a drain current (pulse) i dp pw 10 m s, duty cycle 1% --8.0 a allowable power dissipation p d mounted on a ceramic board (900mm 2 5 0.8mm) 1.2 w channel temperature tch 150 c storage temperature tstg --55 to +150 c electrical characteristics at ta=25 c ratings parameter symbol conditions min typ max unit drain-to-source breakdown voltage v (br)dss i d = -- 1ma, v gs =0 -- 30 v zero-gate voltage drain current i dss v ds = -- 30v, v gs =0 -- 1 m a gate-to-source leakage current i gss v gs = 8v, v ds =0 10 m a cutoff voltage v gs (off) v ds = -- 10v, i d = -- 1ma -- 0.4 -- 1.4 v forward transfer admittance ? yfs ? v ds = -- 10v, i d = -- 1.0a 1.4 2.4 s r ds (on)1 i d = -- 1.0a, v gs = -- 4v 215 280 m w static drain-to-source on-state resistance r ds (on)2 i d = -- 0.5a, v gs = -- 2.5v 290 410 m w input capacitance ciss v ds = -- 10v, f=1mhz 285 pf output capacitance coss v ds = -- 10v, f=1mhz 52 pf reverse transfer capacitance crss v ds = -- 10v, f=1mhz 38 pf turn-on delay time t d (on) see specified test circuit. 10 ns rise time t r see specified test circuit. 33 ns turn-off delay time t d (off) see specified test circuit. 28 ns fall time t f see specified test circuit. 33 ns marking : yf continued on next page. any and all sanyo products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. consult with your sanyo representative nearest you before using any sanyo products described or contained herein in such applications. sanyo assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all sanyo products described or contained herein. n2504 ts im ta-101102
CPH6329 no.8001-2/4 continued from preceding page. ratings parameter symbol conditions min typ max unit total gate charge qg v ds = -- 10v, v gs = -- 4v, i d = -- 2.0a 2.6 nc gate-to-source charge qgs v ds = -- 10v, v gs = -- 4v, i d = -- 2.0a 0.78 nc gate-to-drain miller charge qgd v ds = -- 10v, v gs = -- 4v, i d = -- 2.0a 0.64 nc diode forward voltage v sd i s = -- 2.0a, v gs =0 -- 0.93 -- 1.5 v package dimensions switching time test circuit unit : mm 2151a 1 : drain 2 : drain 3 : gate 4 : source 5 : drain 6 : drain sanyo : cph6 0.05 0.9 0.7 0.2 1.6 0.6 0.6 0.95 1 23 6 5 4 2.8 0.2 2.9 0.15 0.4 pw=10 m s d.c. 1% p. g 50 w g s d i d = --1.0a r l =15 w v dd = --15v v out CPH6329 v in 0v --4v v in 0 --2 --4 --6 --8 --10 200 400 600 800 100 300 500 700 0 200 300 400 250 350 150 500 450 100 r ds (on) -- v gs it07693 0 0 --0.6 --0.9 --1.2 --1.5 --0.2 --0.3 0 --0.6 --0.4 --2.0 --0.8 --1.0 --1.2 --1.4 --1.6 --1.8 --0.2 --1.0 --0.8 --0.6 i d -- v ds it07534 0 --0.5 --1.0 --1.5 --2.0 --2.5 i d -- v gs it07535 r ds (on) -- ta it07694 --60 --40 --20 0 20 40 60 80 100 120 140 160 --0.4 --0.1 --0.9 --0.7 --0.5 --0.3 ta=75 c 25 c --25 c v ds = --10v ta=25 c --1.0a i d = --0.5a i d = --1.0a, v gs = --4.0v i d = --0.5a, v gs = --2.5v --1.5v --2.0v --4.0v --2.5v --3.0v --3.5v v gs = --1.0v drain-to-source voltage, v ds -- v drain current, i d -- a gate-to-source voltage, v gs -- v drain current, i d -- a static drain-to-source on-state resistance, r ds (on) -- m w static drain-to-source on-state resistance, r ds (on) -- m w gate-to-source voltage, v gs -- v ambient temperature, ta -- c
CPH6329 no.8001-3/4 0 0 20 40 60 80 100 120 0.6 0.8 1.0 1.2 0.4 0.2 1.4 140 160 it07685 2 2 3 5 7 2 3 5 7 2 3 5 7 --10 --1.0 --0.1 --0.01 --0.1 23 57 --1.0 --0.01 23 57 23 57 7 --10 23 5 it07684 i dp = --8a i d = --2a operation in this area is limited by r ds (on). 100 m s 100ms 1ms 10ms dc operation (ta=25 c) 0 100 5 7 2 3 5 7 2 3 1000 10 --30 --10 --12 --14 --16 --18 --6 --20 --22 --24 --28 --8 --26 -- 4 -- 2 ciss, coss, crss -- v ds it07541 a s o 2 --0.01 --0.1 23 57 --1.0 5 23 57 23 3 5 2 7 5 7 3 10 100 3 2 5 sw time -- i d it07695 it07539 --0.8 --0.9 --1.0 --1.1 --0.6 --0.7 --1.2 i f -- v sd 0 0 --3.0 --3.5 3 2 1 --4.0 --1.0 --0.5 --1.5 --2.0 --2.5 v gs -- qg it07696 it07538 --0.001 0.1 --0.01 23 57 --0.1 23 57 23 57 --1.0 0.01 5 7 3 2 5 3 2 3 2 5 7 1.0 ? y fs ? -- i d --0.4 --0.5 --0.001 --0.01 --10 --0.1 7 5 3 2 7 5 3 2 --1.0 7 5 3 2 7 5 3 2 p d -- ta ta= --25 c v ds = --10v 75 c 25 c v gs =0 25 c ta=75 c ciss coss crss f=1mhz <10 m s v ds = --10v i d = --2.0a --25 c t r t d (on) t f t d (off) v dd = --15v v gs = --4v forward transfer admittance, ? yfs ? -- s forward current, i f -- a drain current, i d -- a switching time, sw time -- ns drain-to-source voltage, v ds -- v ciss, coss, crss -- pf total gate charge, qg -- nc gate-to-source voltage, v gs -- v drain-to-source voltage, v ds -- v drain current, i d -- a ambient temperature, ta -- c allowable power dissipation, p d -- w drain current, i d -- a diode forward voltage, v sd -- v ta=25 c single pulse mounted on a ceramic board (900mm 2 5 0.8mm) mounted on a ceramic board (900mm 2 5 0.8mm)
CPH6329 no.8001-4/4 specifications of any and all sanyo products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. sanyo electric co., ltd. strives to supply high-quality high-reliability products. however, any and all semiconductor products fail with some probability. it is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. when designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. in the event that any or all sanyo products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of sanyo electric co. , ltd. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equipment, refer to the "delivery specification" for the sanyo product that you intend to use. information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. sanyo believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. this catalog provides information as of november, 2004. specifications and information herein are subject to change without notice. ps note on usage : since the CPH6329 is a mosfet product, please avoid using this device in the vicinity of highly charged objects.
|
